MASONARY COMPOUND
SUPER STRONG PRODUCT
Tile adhesive is a thin set mortar applied over the masonry surface to lay tiles or slabs
Previous
Next
DRYMIX
FLOOR TILE ADHESIVE
Main Features
SIMCRETE FLOOR TILE ADHESIVE consists of cement, dried sand, additives, and polymers formulated for tiling application.
Features & Benefits
Designed to meet the exacting needs of tiling professionals- Ready to use product just requiring the addition of clean water
- Quality premixed product specifically formulated for tile bedding applications
- Excellent workability
- Designed to ensure that tiles ‘sit up’ on the bedding mix and reduces slumping
- Floor Tile bedding mortar is designed to retain moisture to assist natural hydration process especially at warm to hot temperatures
Applications
- Bedding floor tiles
- General floor tile applications
Packaging
Product available in 20kg bags
One 20kg bag of Rapid Set Concentrate requires approximately 20% by volume of pure water to provide workable mix
50 – 60 sqft/20 Kg. Bag at 3 mm thickness
30 – 40 sqft/20 Kg Bag at 6 mm thickness
Product Specification
Mechanical / Physical Properties
| Property | Type | Details |
|---|---|---|
| Tensile Adhesion Strength | Dry | 1440 N |
| Wet | 1000 N | |
| Compressive Strength | @ 28 days | 13.6 N/mm2 |
| POT LIFE | 225 minutes | |
| OPEN TIME | 90 minutes |
Composition
COMPOSITION
| Sl | Type | Details |
|---|---|---|
| 1 | Mortar (Graded Sand & Cement) | 93-95% |
| 2 | Additive 1 | 5% |
| 3 | Additive 2 | 0.7% |
| 4 | Polymer | 0.7% |
Mix Density
~ 1.6 to 1.7 gram /cc
- Download technical document
- Inspiration gallery
Directions for use
- Place the required amount of Drymix Floor Tile Adhesive into a mixer or onto a non-absorbent surface
- Add potable water gradually ensuring that it does not wash away any cement and mix thoroughly
to ensure an even and consistent mix (NOTE : Add enough water to make a workable mix and do not add excessive water as this will weaken the Drymix Floor Tile Adhesive. The recomended amount of water should be added to ensure that the bedding mortar is moist enough to bond to the tiles but not so wet that it sags or runs down). - Form a mortar bed of approximately 3 to 6 mm thick from end to end using a grooved trowel.
- Place the tile on the bed of mortar and remove any excess mortar that may be squeezed out when the tile
is placed and smoothen the joint. Any gaps that become apparent must be filled with mortar allowing
it to dry before finishing with a ‘pointing’ mix applied in line with the manufacturers
recommendations. - All tools and equipment should be cleaned with water after use.
- Do not re-temper the mortar if it stiffens. Discard the stiffened product and make a new mix
- Tips & Videos
- Inspiration gallery
DRYMIX
TILE ADHESIVE-REGULAR
Main Features
SIMCRETE TILE ADHESIVE - REGULAR consists of cement, dried sand, additives & polymers and is suitable for bedding tiles.
Features & Benefits
- Designed to meet the exacting needs of tiling professionals
Ready to use product just requiring the addition of clean water - Quality premixed product specifically formulated for tile bedding applications
- Excellent workability
- Designed to ensure that tiles ‘sit up’ on the bedding mix and reduces slumping
- Tile Bedding Mortar is designed to retain moisture to assist natural hydration process especially at warm to hot temperatures
Applications
- Bedding floor tiles
- Bedding wall tiles
- General tile applications
Packaging
Product available in 20kg bags
One 20kg bag of Simcrete Tile Adhesive – Regular requires approximately 18 – 20% by weight of pure water to provide workable mix.
50 – 60 sqft/20 Kg. Bag at 3 mm thickness
30 – 40 sqft/20 Kg Bag at 6 mm thickness
30 – 40 sqft/20 Kg Bag at 6 mm thickness
Product Specification
Mechanical / Physical Properties
| Property | Type | Details |
|---|---|---|
| Tensile Adhesion Strength | Dry | 2862 N (Dry) |
| Wet | 1567 N (Wet) | |
| Heat Aging | @ 14 days | 6.6 N/mm2 |
| Compressive Strength | @ 28 days | 16.4 N/mm2 |
| Shear Adhesion Strength | Wet | 2.85 kN (Dry) @ 24 hrs |
| Wet | 8.22 kN (Dry) @ 14 hrs | |
| Wet | 5.88 kN (Wet) @ 14 days | |
| Adjustability | 50 minutes | |
| POT LIFE | 3 Hours | |
| OPEN TIME | 45 minutes |
Composition
COMPOSITION
| Sl | Type | Details |
|---|---|---|
| 1 | Mortar (Graded Sand & Cement) | 90-93% |
| 2 | Additive 1 | 7% |
| 3 | Additive 2 | 0.4% |
| 4 | Polymer | 0.6% |
Mix Density
~ 1.8 to 1.85 gram /cc
- Tips & Tutorials
- Inspiration gallery
Directions for use
- Place the required amount of Wall Tile Adhesive-Regular into a mixer or onto a non-absorbent surface.
- Add potable water gradually ensuring that it does not wash away any cement and mix thoroughly
to ensure an even and consistent mix (Note: Add enough water to make a workable mix and do not add excessive water as this will weaken the Dry-Mix Wall Tile Adhesive-Regular. The recommended amount of water should be added to ensure that the bedding mortar is moist enough to bond with the tiles but not so wet that it sags or runs down). - Form a mortar bed of approximately 3 to 6 mm thick from end to end using a grooved trowel
- Place the tile on the bed of mortar and remove excess mortar that may be squeezed out when the tile
is placed and smoothen the joint. Any gaps that become apparent must be filled with mortar allowing
it to dry before finishing with a ‘pointing’ mix applied in line with the manufacturers
recommendations. - All tools and equipment should be cleaned with water after use.
- Do not re-temper the mortar if it stiffens. Discard the stiffened product and make a new mix
- Tips & Videos
- Inspiration gallery
DRYMIX
TILE ADHESIVE-SUPER +
Main Features
SIMCRETE TILE ADHESIVE-SUPER +, consists of cement, dried sand, additives, and polymers.
Features & Benefits
Designed to meet the exacting needs of tiling professionals
- Ready to use product just requiring the addition of clean water
- Quality premixed product specifically formulated for tile bedding applications
- Excellent workability
- Designed to ensure that tiles ‘sit up’ on the bedding mix and reduces slumping
- Tile Bedding Mortar is designed to retain moisture to assist natural hydration process especially at warm to hot temperatures
Applications
- Bedding stone slabs & floor tiles
- Bedding stone slab wall cladding
- General slab & tile applications
Packaging
Product available in 20kg bags
One 20kg bag of Simcrete Tile adhesive- Super + requires approximately 20% by weight of pure water to provide a workable mix.
50 – 60 sqft/20 Kg. Bag at 3 mm thickness
30 – 40 sqft/20 Kg Bag at 6 mm thickness
30 – 40 sqft/20 Kg Bag at 6 mm thickness
Product Specification
Mechanical / Physical Properties
| Property | Type | Details |
|---|---|---|
| Tensile Adhesion Strength | Dry | 1373 N (Dry) |
| Wet | 847 N (Wet) | |
| Heat Aging | @ 14 days | 6.6 N/mm2 |
| Compressive Strength | @ 28 days | 16.4 N/mm2 |
| Shear Adhession Strength | Wet | 3.07 N/mm2 |
| Wet | 8.2 N/mm2 | |
| Adjustability | 50 minutes | |
| POT LIFE | 3 hours | |
| OPEN TIME | 45 minutes |
Composition
COMPOSITION
| Sl | Type | Details |
|---|---|---|
| 1 | Mortar (Graded Sand & Cement) | 90-92% |
| 2 | Additive 1 | 8% |
| 3 | Additive 2 | 0.4% |
| 4 | Polymer | 0.6% |
Mix Density
~ 1.8 to 1.87 gram /cc
- Tips & Tutorials
- Inspiration gallery
Directions for use
- Place the required amount of Drymix Tile/Stone Adhesive-Super + into a mixer or onto a
non-absorbent surface - Add potable water gradually ensuring that it does not wash away any cement and mix thoroughly
to ensure an even and consistent mix (Note: Add enough water to make a workable mix and do not add excessive water as this will weaken the Tile Adhesive-Super +. The recommended amount of water should be added to ensure that the bedding mortar is moist enough to bond with the tiles, but not so wet that it sags or runs down). - Form a mortar bed of approximately 4 to 6 mm thick from end to end using a grooved trowel
- Place the tile on the bed of mortar and remove any excess mortar that may be squeezed out when the tile
is placed and smoothen the joint. Any gaps that become apparent must be filled with mortar allowing
it to dry before finishing with a ‘pointing’ mix applied in line with the manufacturers
recommendations. - All tools and equipment should be cleaned with water after use.
- Do not re-temper the mortar if it stiffens. Discard the stiffened product and make a new mix
- Tips & Videos
- Inspiration gallery
Latest Posts
- BLOG
Why Simcrete?
Looking for something that is durable and strong?
We have a tile adhesive that leaves an impeccable finish on the floor and wall for a long time to come.
Our Silica Sand Based tile adhesive is easy to use, eco- friendly, authentic and cement-based.
- Watch our video
Clients List
Testimonials
"After using Simcrete Wall Plaster in one of our project , all I can say is, this product is simply awesome, and above standards of other brand. Try it and you'll love it!"
sreedar reddy
Project Head
"After using Simcrete Wall Plaster in one of our project , all I can say is, this product is simply awesome, and above standards of other brand. Try it and you'll love it!"
Paras Shah
Purchase Manager
